Hayter Electrical
Keep your Hayter running reliably with genuine Hayter electrical parts that ensure dependable starting, consistent spark delivery, and proper battery charging. Our comprehensive range of Hayter mower electrical components includes ignition coils, spark plugs, starters, batteries, charging system parts, safety switches, and complete wiring harnesses designed specifically for your model. Hayter replacement electrical parts feature OEM specifications for voltage output, resistance values, and connector compatibility across Harrier 41, Harrier 48, Harrier 56, Spirit, and Ranger models. Stocked at our UK facility with express delivery available nationwide and international shipping worldwide.
Available Hayter Electrical
Engine B&S 850E Recoil Tapered Crank
134-2143
Hayter
£213.81
Available
Switch and Loom
111-8392
Hayter
£55.60
In Stock
Switch and Lead Assembly
111-1841
Hayter
£26.31
In Stock
Switch-Left, Lower
HY100021
Hayter
£1.98
In Stock
Switch and Lead Asm
100515
Hayter
£32.53
In Stock
Pto Switch
93-9998
Hayter
£44.34
In Stock
Starter Switch Asm
46-5780
Hayter
£29.90
In Stock
Ignition Switch (Hb)
MU92377
Hayter
£23.42
Available
Microswitch
510068
Hayter
£120.82
Available
Rocker Switch
92-8875
Hayter
£16.49
Available
Module Switch (Honda Es)
110-1787
Hayter
£53.62
Available
Limit Switch (Hb)
MU1001575
Hayter
£9.42
View More
Frequently Asked Questions
How do I diagnose why my Hayter mower has no spark at the spark plug?
If your Hayter shows no spark, first disconnect the kill wire from the ignition coil and test again—if spark appears, the problem is in the safety switch wiring or operator presence control. Check the ignition coil air gap using a feeler gauge; it should measure between 0.006" and 0.014" from the flywheel magnets. Test the Hayter electrical parts with a spark tester while cranking at minimum 350 RPM. Replace the ignition coil if the gap is correct but no spark occurs.
What causes a Hayter mower battery to drain while the engine is running?
A battery that drains during operation indicates charging system failure in your Hayter mower electrical components. The stator generates AC voltage (minimum 28 volts AC at three-quarter throttle) that the regulator-rectifier converts to 13.8-14.7 volts DC for battery charging. Test stator output with a multimeter set to AC voltage on the yellow wires beneath the blower housing. If AC voltage is present but DC output is absent, replace the voltage regulator.
Can aftermarket Hayter replacement electrical parts cause starting problems?
Yes, aftermarket ignition coils and spark plugs frequently cause reliability issues compared to genuine Hayter electrical parts. Inferior coils may produce weak spark when cold and fail completely when hot, while incorrect spark plug heat ranges cause fouling, pre-ignition, or hard starting. Aftermarket parts often lack proper quality control for resistance values and voltage output specifications. Use genuine Hayter mower electrical components to ensure proper fitment, correct specifications, and reliable long-term performance.
What is the correct ignition coil air gap for Hayter mowers?
The proper air gap between the Hayter ignition coil and flywheel magnets ranges from 0.006 inch to 0.014 inch depending on your engine model. Set the gap by rotating the flywheel until magnets align with the coil, inserting a 0.010-inch feeler gauge, loosening mounting screws, allowing magnets to pull the coil against the gauge, then tightening screws. Incorrect gap prevents the coil from generating sufficient voltage to fire the spark plug reliably.
How do I test if my Hayter charging system is working properly?
Test your Hayter mower electrical components charging system by connecting a voltmeter to the battery terminals with the engine running at full throttle. A properly functioning system produces 13.8-14.7 volts DC. If voltage stays at 12.6 volts or drops, the charging system has failed. Disconnect the regulator and test stator AC output—it should exceed 28 volts AC. If stator output is good but DC voltage is low, replace the voltage regulator; if AC output is insufficient, replace the stator.