Hayter Ignition Coils
Ensure reliable spark generation with genuine Hayter ignition coils engineered to deliver consistent high-voltage output for dependable starting and smooth engine operation. Hayter ignition coil parts feature solid-state Magnetron technology that generates the electrical spark needed to ignite the air-fuel mixture in your combustion chamber. Our Hayter mower ignition coils include precise lamination stacks, correct resistance specifications (2,500-5,000 ohms), and factory-set air gap tolerances for optimal magnetic field interaction with flywheel magnets. Designed for Harrier 41, Harrier 48, Harrier 56, Spirit, and Ranger engines. Available for immediate worldwide dispatch with rapid UK delivery.
Available Hayter Ignition Coils
Engine B&S 850E Recoil Tapered Crank
134-2143
Hayter
£213.81
Available
Ignition Coil Assy
MY267580
Hayter
£85.68
Available
Ignition Coil Assy
MY267173
Hayter
£70.50
View More
Engine-1P65FC, Recoil [2800, Serv]
144-1018
Hayter
--
View More
Recoil and Blower Shroud
121-4160
Hayter
£57.75
Available
Engine, B&S 850E Recoil
111-9693
Hayter
£327.30
Available
Engine, B&S 850E Recoil Bbc
111-9694
Hayter
£287.72
Available
Brake Asm Recoil Kit
119-1991
Hayter
£41.25
Available
Coil Asm-Ignition (Tec)
138-9149
Hayter
£27.60
Available
Engine-1P65Fc, Recoil
147-7104
Hayter
£160.96
Available
Nut-Coil (1/2-20 Unf-2B)
130-8181
Hayter
£26.37
Available
Pin-Coil
32121-99
Hayter
£1.02
Available
Frequently Asked Questions
How do I test if my Hayter ignition coil is faulty using a multimeter?
Test your Hayter mower ignition coil by setting a multimeter to ohms resistance and measuring between the spark plug terminal and the lamination stack ground. A healthy Hayter ignition coil reads 2,500-5,000 ohms at room temperature. Infinite resistance indicates an internal open circuit, while zero ohms means a short circuit—both require replacement. Readings significantly above 5,000 ohms indicate deteriorating windings that produce weak spark and cause starting difficulties.
Why does my Hayter start when cold but stops running when hot?
A Hayter ignition coil that works cold but fails hot exhibits classic heat-related breakdown where internal insulation resistance deteriorates as temperature rises, causing the coil to short internally. Test by installing an inline spark tester and running the engine until it stops—watch for diminishing spark intensity. This "dying coil" symptom requires Hayter ignition coil parts replacement. Aftermarket coils frequently fail this way; always use genuine Hayter ignition coils for reliable performance.
What causes weak spark from a Hayter mower ignition coil?
Weak spark from Hayter ignition coils results from several factors, including an incorrect air gap (should be 0.006-0.014 inches from flywheel magnets), excessive resistance in secondary windings above 5,000 ohms, corrosion on flywheel magnets reducing magnetic field strength, or using aftermarket coils with inferior materials. Additionally, ensure engine cranking speed exceeds 350 RPM minimum—below this threshold, coils cannot generate sufficient voltage. Test with an inline spark tester rather than laying the plug against the block.
Can I adjust the Hayter ignition coil to improve spark output?
The only adjustment on Hayter ignition coil parts is the air gap between the coil armature and flywheel magnets. Set the gap by rotating the flywheel until magnets align with the coil, inserting a 0.010-inch feeler gauge or business card thickness shim, loosening mounting screws, allowing magnets to pull the coil against the shim, then tightening screws. Remove the shim and rotate the flywheel to verify clearance. Incorrect gap prevents proper magnetic field generation regardless of coil condition.
Should I disconnect the kill wire when testing my Hayter ignition coil?
Always disconnect the kill wire from your Hayter mower ignition coil before testing to eliminate safety switch wiring as a variable. The kill wire grounds the coil to stop the engine—if it's shorted to ground through damaged wiring or faulty switches, the Hayter ignition coil cannot produce spark even when functioning perfectly. Test with kill wire disconnected: if spark appears, the coil works and the problem is in safety switch circuits; no spark indicates coil replacement needed.